Use the metric o-ring size chart to find common metric o-ring sizes by cross section, inside diameter, and outside diameter. In addition to standard metric o-ring sizes, thousands of non-standard metric o-rings sizes are available in stock or can be custom-made within a few weeks, usually without additional tooling fees.

May 17,  · Parker’s new O-Ring Selector is an engineering design tool that enables users to make the right material and size selections easily, quickly and reliably – in a single application. This post explains how to design the sealing system using the “Size Selector.” See also related blog posts: O-Ring Selection Made Easy with the Parker O-Ring

Parker´s O-Ring Selector is an engineering tool which offers O-ring material and size selection combined in one tool. Both are interlinked, thus ensuring the best possible combination of the calculated O-ring size and material choice. The O-Ring Selector covers both imperial and metric standards. Service Conditions & Material Selector

Learn how to size and select O-Rings Base Mobile, Seal Design, Web. parkerhannifin. Parker Hannifin. 430 followers Parker's O-Ring Calculator 

Buy Parker's Seal-Lok O-Ring Face Seal (ORFS) tube fittings and adapters to achieve leak-free connections for use in high pressure and high vibration environments; meet SAE J1453 and ISO 8434-3 standards. Connection 3 Thread Size: SAE-ORB Sizes 7/16-20 to 2 1/2-12, NPT/NPTF Sizes 1/8-27 to 1 1/2-11 1/2 and BSPP Sizes 1/8-28 to 1 1/2-11

Standard and Metric O-Rings Dimensions There are two main o-ring sizing types: standard and metric. Standard was developed for use in the United States, while 

Nominal (inches) Nominal (inches) Nominal (inches) Actual (inc Parker Size AS568A; Size ID OD W ID 2‑001 ‑001 1/32 3/32 1/32 .029 2‑002 ‑002 3/64 9/64 3/64 .042

Parker 500 Series O-Rings ; 5-001 · 0.547 ; 5-002 · 0.416 ; 5-003 · 0.836 ; 5-004 · 1.07 ; 5-005 · 0.64.

The Parker O-Ring Handbook has been a standard reference work 3.2.1 Hydraulic – compression and design dimensions. . . . . . 34.

Parker 5‑XXX Size CS (MM) ID (MM) CS (IN) ID (IN) 5‑002 1.50 10.57 0.059 0.416 5‑003 1.50 21.23 0.059 0.836 5‑004 1.65 27.18 0.065 1.070

b) This chart provides dimensions for standard (AN) shrinkage materials ONLY. These correspond to AS568A dimensions. O-rings manufactured out of compounds 

Oct 22,  · A Guide to Ordering Parker O Rings. Oct 22, . If you’ve worked on a project where sealing was needed, chances are you’ve worked with an o-ring. They are the most commonly used seal in the world, made from a variety of materials across the size spectrum. Their popularity comes from being a cost-effective and efficient sealing method, in

Table 9-1: Parker Series 2-XXX O-Ring Sizes Parker Series 2-XXX O-Ring Sizes 12 3 4 5 6 7 Parker Size No. (Size Only) (a) Size Only Nominal Size (Inches) Standard O-Ring Size (Units are in

Parker O-Ring Handbook Parker Series 5-XXX O-Ring Sizes (Continued) (a) The rubber compound must be added when ordering by the 5-size number (i.e., N0674-70 5-007). (b) This

Resilon® Polyurethane O-Rings (568) Resilon® polyurethane O-rings for hydraulic and pneumatic applications, static and dynamic AS568B specification size O-ring grooves (568). Configure

PDF] Available O-Ring Tooling Sizes AS568 is the Aerospace Size Standard for O-rings from the Society of Automotive Engineers. SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. Please add the material

O-Ring Face Seal Glands These dimensions are intended primarily for face type O-ring seals and low temperature applications. O-Ring. Size. Parker.

Use our o-ring size chart and calculator to find the AS568 or metric sizing of standard size HNBR, Viton, and other o-rings. Go to Navigation Go to Content. O-ring Sizes: Standard and Metric : Size: Nominal Size: Standard Size : Metric Size : inches: inches : millimeters :

O-rings are circular sealing elements with circular cross-sections, and are mainly used in static applications. The sizes are specified by the inside diameter and the cross section diameter. Our O-rings are manufactured according to metric and imperial international standards such as AS 568B, DIN ISO 3601 and JIS. Custom sizes of almost any dimension are possible, such as

Parker's Fluorocarbon 50 Durometer O-Ring, General Purpose , Brown V0986-50 is the softest FKM material offered for O-rings. V0986-50 has excellent compression set resistance coupled with the wide chemical resistance expected of a fluorocarbon. *Custom sizes and coatings/markings are available upon request. Contact Parker O-Ring Division at

Parker Hannifi n Corporation • O-Ring Division I 2360 Palumbo Drive, Lexington, KY 40509 Phone: (859) 269-2351 † Fax: (859) 335-5128 www.parkerorings.com Parker O-Ring Handbook 5500tthh AAnniversarynniversary EEditiondition Since its initial release in 1957, the Parker O-Ring Handbook has become a fi xture on the reference